RUT202 4G/LTE CAT4 INDUSTRIEL ROUTER

RUT202 - COMPACT INDUSTRIAL DUAL SIM ROUTER RUT202 is our smallest dual sim industrial LTE Cat 4 router built for stable and continuous connectivity, featuring Dual SIM with automatic failover to prevent network interruptions. Its space-efficient aluminium housing fits easily into tight or embedded installations, while dual Ethernet ports and LTE + Wi-Fi support enable flexible wired and wireless setups. RUT202 combines dual SIM redundancy, compact housing, and internal SIM security in a single, easy-to-deploy device. Mobile Mobile module: 4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8 UL kbps 3GPP Release: Release 9 SIM switch: 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail Status: IMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC SMS: SMS status, SMS configuration, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP USSD: Supports sending and reading Unstructured Supplementary Service Data messages Block/Allow list: Operator block/allow list (by country or separate operators) Multiple PDN: Possibility to use different PDNs for multiple network access and services Band management: Band lock, Used band status display SIM PIN code management: SIM PIN code management enables setting, changing, or disabling the SIM card's PIN APN: Auto APN Bridge: Direct connection (bridge) between mobile ISP and device on LAN Passthrough: Router assigns its mobile WAN IP address to another device on LAN Wireless Wireless mode: 802.11b/g/n (Wi-Fi 4), Access Point (AP), Station (STA) Wi-Fi security: WPA2-Enterprise: PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect, 802.11w Protected Management Frames (PMF) SSID/ESSID: SSID stealth mode and access control based on MAC address Wi-Fi users: Up to 50 simultaneous connections Wireless Connectivity Features: Fast roaming (802.11r), Relayd, BSS transition management (802.11v), radio resource measurement (802.11k) Wireless MAC filter: Allowlist, blocklist Wireless QR code generator: Once scanned, a user will automatically enter your network without needing to input login information TravelMate: Forward Wi-Fi hotspot landing page to a subsequent connected device Ethernet WAN: 1 x WAN port 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover LAN: 1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover Input/Output Input: 1 x Digital Input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high Output: 1 x Digital Output, Open collector output, max output 30 V, 300 mA Events: Email, RMS, SMS I/O juggler: Allows to set certain I/O conditions to initiate event Power Connector: 4-pin industrial DC power socket Input voltage range: 9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max PoE (passive): Passive PoE over spare pairs. Possibility to power up through LAN1 port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, 9 - 30 VDC Power consumption: < 6.5 W Max Physical Interfaces Ethernet: 2 x RJ45 ports, 10/100 Mbps I/O’s: 1 x Digital Input, 1 x Digital Output on 4-pin power connector Status LEDs: 3 x Connection type status LEDs, 3 x Connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED SIM: 2 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V, internal SIM holders Power: 1 x 4-pin power connector Antennas: 2 x SMA for LTE, 1 x RP-SMA for Wi-Fi antenna connectors Reset: Reboot/User default reset/Factory reset button Physical Specification Casin