RUT204 4G/LTE CAT4 CAN BUS ROUTER

RUT204 CAN BUS LTE ROUTER Designed for efficient machine data connectivity, the RUT204 combines native CAN FD hardware with LTE Cat 4 to enable direct and secure transmission of CAN data without external converters. Support for CANOpen and J1939 allows seamless integration with CAN based equipment. Built for industrial and mobile applications, this compact router also features GNSS for asset tracking, Wi-Fi 4, Dual SIM, PoE-in, RS232, Ethernet, and a wide 9 - 57 VDC power range. Embedded RutOS and RMS support enable zero touch deployment, remote monitoring, and scalable fleet management to reduce complexity and improve operational efficiency. Mobile Mobile module: 4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8 UL kbps 3GPP Release: Release 9 SIM switch: 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection Status: IMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC SMS: SMS status, SMS configuration, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP USSD: Supports sending and reading Unstructured Supplementary Service Data messages Block/Allow list: Operator block/allow list (by country or separate operators) Band management: Band lock, Used band status display SIM idle protection service: Provides the possibility to configure the router to periodically switch to the unused SIM card and establish a data connection in order to prevent the SIM card from being blocked SIM PIN code management: SIM PIN code management enables setting, changing, or disabling the SIM card's PIN APN: Auto APN Bridge: Direct connection (bridge) between mobile ISP and device on LAN Passthrough: Router assigns its mobile WAN IP address to another device on LAN Wireless Wireless mode: 802.11b/g/n (Wi-Fi 4), Access Point (AP), Station (STA) Wi-Fi security: WPA2-Enterprise: PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect, 802.11w Protected Management Frames (PMF) SSID/ESSID: SSID stealth mode and access control based on MAC address Wi-Fi users: Up to 50 simultaneous connections Wireless Connectivity Features: Fast roaming (802.11r), Relayd, BSS transition management (802.11v), radio resource measurement (802.11k) Wireless MAC filter: Allowlist, blocklist Wireless QR code generator: Once scanned, a user will automatically enter your network without needing to input login information TravelMate: Forward Wi-Fi hotspot landing page to a subsequent connected device Ethernet WAN: 1 x WAN port 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover LAN: 1 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover MODBUS Supported modes: Server, Client Supported connection types: RTU(RS232) Custom registers: MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality Supported data formats: 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII CAN CAN Gateway: Allows forwarding CAN frames over IP networks. CANopen SDO Client (Planned): Allows data collection and monitoring from other devices SAE J1939 Client (Planned): Allows data collection and monitoring from other devices Serial RS232: RS232 only TX and RX signals CAN: Integrated CAN interface Serial functions: Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client Input/Output Events: Email, RMS,